[. . . ] Installation Manual for the
DC-SERIES
®
DC-SERIES
!
®
WARNING
Can Cause Injury or Death
MOVING GATE
1-800-543-GATE (4283) · www. gtopro. com
SINGLE Gate Operator System FOR PROFESSIONAL INSTALLATION ONLY!
WARNING!
This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions. Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. [. . . ] · The operator is level and mounted on the centerline of the gate.
C L
Closed Position Stop Plate
Gate In Closed Position
Mounting the Control Box
15
ALARM BAT BAT+
800-543-GATE
www. gtoinc. com
Step 13
Mount the control box using the screws (provided) or another secure mounting method. The control box must be mounted at least 3 feet above the ground to protect it from rain splash, snow, etc. , and at least 3 feet from an AC power source to prevent electrical interference.
Use mounting holes and screws provided to mount control box to a secure surface.
FUSE SWITCH
GTO, Inc. 3121 Hartsfield Rd Tallahassee, FL 32303
1234
DUAL ON MODES
1 2 3 4
ON
OFF
SET LIMIT
MODES ON
1
1 2 3 4 5 6 7 ON
2 3 4 5 6 7
OFF LEARN TRANSMITTER
SWITCH
10'
12' 14'
8' GATE LENGTH
16'
~~ 18VAC
+ NC RLY-COM NO SOLAR RELAY OUT
SHADOW LOOP
SAFETY
CYCLE CLOSE
EXIT/ OPEN
SLAVE INPUTS
MASTER INPUTS
OPEN EDGE
GRN WHT BLUE
BRN ORG
RED
BLK
GRN WHT BLUE
BRN ORG
RED
BLK
COM COM
CLOSE EDGE
GRN BLK
RED
RECEIVER
NOTE: The battery that came with your GTO/PRO® 3000 , MUST be placed horizontally battery with the terminals on the RIGHT. If an optional second battery is needed, both batteries must be placed vertically with terminals at the bottom. An optional second battery can be used for solar and/or high traffic applications, if needed. .
Single Battery Installed Horizontally with terminals on the right.
Dual Batteries Installed Vertically with terminals on bottom.
17
Connecting Operator Power Cable
Step 14
Make sure the control box power switch is in the OFF position. Remove the control box cover and slide the battery into position with its terminals to the RIGHT (see illustration). Connect the BLACK battery wire to the NEGATIVE () battery terminal. If the wires are connected incorrectly, the control board may be damaged. NEVER insert the battery with the terminals to the left.
BLACK wire to NEGATIVE (--) terminal RED wire to POSITIVE (+) terminal
BLACK RED
12 V Battery (Included)
Step 15
Strip approximately 3/16" of insulation from each wire of the operator power cable. Twist each exposed wire tightly (there are seven [7] wires inside the power cable sheath). Thread approximately 6" of the power cable into the control box and retighten sealing nut until the power cable locks into place.
15
FUSE SWITCH
GTO, Inc. 3121 Hartsfield Rd Tallahassee, FL 32303
ALARM BAT BAT+
800-543-GATE
www. gtoinc. com
1234
DUAL ON MODES
1 2 3 4
ON
OFF
SET LIMIT
MODES ON
1
1 2 3 4 5 6 7 ON
2 3 4 5 6 7
OFF LEARN TRANSMITTER
SWITCH
10'
12' 14'
8' GATE LENGTH
16'
~~ 18VAC
+ NC RLY-COM NO SOLAR RELAY OUT
SHADOW LOOP
SAFETY
CYCLE CLOSE
EXIT/ OPEN
SLAVE INPUTS
MASTER INPUTS
OPEN EDGE
GRN WHT BLUE
BRN ORG
RED
BLK
GRN WHT BLUE
BRN ORG
RED
BLK
COM COM
CLOSE EDGE
GRN BLK
RED
RECEIVER
Strain Relief
Lock Nut Hub
SWITCH
Sealing Nut
Strain Relief
GRN WHT BLUE BRN ORG
Operator Power Cable
J13
MASTER INPUTS
Step 16
Insert the stripped operator power cable wires into the appropriate terminals on the OPERATOR terminal block. The green wire should be inserted into the GRN terminal, the blue wire into BLU, the orange wire into ORG, black wire into BLK, and the red wire into the RED terminal. A dab of petroleum jelly on each terminal will help prevent corrosion. Do not overtighten.
RED
J5
BLK
Power cable from operator (master) arm
CYCLE CLOSE SAFETY EXIT OPEN SHADOW LOOP CLOSE EDGE OPEN EDGE
COM COM GRN
J11 J8
MIN
STALL FORCE
RECEIVER
Correct
Wrong
Wrong
J12
Wire
Terminal Block
Wire
Terminal Block
Wire
Terminal Block
18
MAX
BLK RED
Powering the System
Installation of the Transformer
IMPORTANT:
· The transformer is designed and intended for indoor use. If the transformer can be plugged only into an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores) must be used. All low voltage wire used with the GTO/PRO® 3000 Gate Operator must be 16 gauge dual conductor, multi-stranded, direct burial wire (see page 20) and the Accessory Catalog). from an ac power source, you will need to use at least one 5 watt Solar Panel to charge the battery (see Accessory Catalog). Refer to the Solar Panels and Gate Activity chart below.
·
·
Optional Solar Panels and Gate Activity
The table and map illustrate the maximum number of gate cycles to expect per day in a particular area when using from 5 to 30 watts of solar charging power. The figures shown are for winter (minimum sunlight) and do not account for the use of any accessory items. Accessories connected to your system will draw additional power from the battery. NOTE: A maximum of 30 watts of solar charging power can be connected to the GTO/ PRO® Gate Operator. [. . . ] Wires directly to the control board and uses 16 gauge multi-stranded, dual conductor low voltage wire (sold separately).
Pin Lock (RB975)
The Pin Lock substitutes for the clevis pin at the front end of the GTO/PRO® 3200 gate operator. Helps prevent theft of the operator from the gate, while allowing quick release of the operator.
Key Chain Mini Transmitter (RB744)
The Key Chain Mini Transmitter is a miniature version of the GTO/PRO® 3200 entry transmitter and has the same adjustable code settings. 12 Volt battery included.
Entry Transmitter (RB741)
The GTO/PRO® entry transmitter, with adjustable code settings, is standard equipment with all GTO/PRO® 3200 systems. 9 Volt battery included.
Digital Keypad (F300)
1 4 7 2 5 8 0 3 6 9
The specially designed digital keypad can be easily installed as a wireless or wired keypad. [. . . ]